Herramientas en acción: Llave de cinta - Reed Manufacturing (LatinoAmérica) - video Dailymotion

ReedManufacturingCompany

Use las llaves de cinta para tubo plástico, filtros o cualquier superficie resbaladiza o lisa. Las llaves de cinta también funcionan bien sobre perfiles irregulares. La cinta recubierta en poliéster extra resistente de Reed ofrece durabilidad, resistencia al deslizamiento y además protege el tubo plástico o de metal pulido contra rayas o deformaciónes. SW12A30, SW18A48 y SW24A72 tienen cintas extralargas para mayor efecto palanca en los diámetros grandes.   Más información: https://www.reedmfgco.com/es/products/wrenches/strap-wrenches/?utm_source=social&utm_medium=dailymotion   Encuentre un distribuidor cerca de usted: https://www.reedmfgco.com/es/where-to-buy/?utm_source=social&utm_medium=dailymotion   ¡Conectemos!  Facebook: https://www.facebook.com/reedlatinoamerica  Instagram: https://www.instagram.com/reedlatinoamerica  YouTube: http://www.youtube.com/@ReedPipeTools  TikTok: https://www.tiktok.com/@reedpipetools   #ReedPipeTools #ReedLatAm #HerramientasIndustriales #latam #llaves #llavedecinta

Transcript

00:00R.I.T.H. presents the R.I.T.H. tape key.

00:10It is a light, portable and easy-to-use tool.

00:14Its main advantage is the strength of support

00:17that it exerts without scratching or deforming plastic or metal pipes.

00:21Its ductile iron handle and resistant polyester tape

00:26make it a durable tool,

00:28ideal for use on slippery, smooth or irregular surfaces.

00:33In addition, it can be used with tapes of various sizes

00:37to cover a greater number of diameters.

00:43To begin, we must place the pipe in the accessory where we want to attach it,

00:49first as far as our hands allow us.

00:59Once done, we will have to use the tape key to adjust the joint as much as possible.

01:06Next, we will proceed to explain the two possible techniques to use the tape key.

01:12For the first one, we must correctly locate the arc of the tool, which is the following.

01:19This arc must point in the direction in which I need to screw.

01:23In this case, the pipe must screw in this direction.

01:26Therefore, the arc will point in that direction.

01:32In this way.

01:35Then, I will run the tape around the pipe

01:39and I will place it again in the buckle, in this case, below the tool.

01:47And I will proceed to adjust.

01:50And I will proceed to adjust.

01:52Once adjusted, before using the tool, I must loosen the tape a little

01:58so that I give space to the head to turn completely.

02:03In this way.

02:09And I will proceed to turn and screw the pipe.

02:14As you can see, it is a smooth surface that holds perfectly

02:19and allows me to screw very easily and effortlessly.

02:22For the second technique, we will first pass the tape through the top of the tool,

02:30in this way, without holding anything.

02:34Once in that position, we will locate the arc in the correct position.

02:38Once in that position, we will locate the arc in the correct position.

02:41In the first technique, the tool should have been in this direction

02:45because I want to turn in this way.

02:47But for this technique, it must be done in the opposite way.

02:51In this way.

02:53I will pass the belt around the pipe

02:58and I will pass the tape through the same hole where I had inserted the first time.

03:08And I will screw in this way.

03:10Again, before I can apply pressure, I must give enough tape to the tool

03:14so that it can turn in this way.

03:19And again, I start to turn.

03:33At the end, I release the tape

03:39and I keep it for the next operation.

03:45Finally, remember that just as we inserted the tube in the accessory,

03:49the reverse process can also be done,

03:52insert the accessory in the tube,

03:54since some accessories have an irregular surface.

04:08Again, at the end of the process,

04:11release the tape and keep it for the next operation.

04:15Remember to wear gloves at all times.

04:19To know more, in the description you will find technical information

04:22and the contact of our specialists.

04:24And for more tools, do not forget to visit our website.

04:27See you in the next video.

04:38www.ottobock.com

Herramientas en acción: Llave de cinta - Reed Manufacturing (LatinoAmérica)

Category

Transcript

Recommended