title
ap fan motor rewinding
about
Doston repairing channel Mein aapka swagat hai aaj main aapke liye AP motor ko winding karne wala hun AP motor ko Kis Tarah Se winding karte hain aur Kaise connection karte hain yah sab aaj main aapko is video mein bataunga isliye video pura Dekhen video Pasand I like Karen doston ke sath channel ko share Karen thank u
playlist
Ap motor
https://dailymotion.com/rss/playlist/x8wz6s
#repairingchannel
#apfan
#motor
#rewinding
ap fan motor rewinding
about
Doston repairing channel Mein aapka swagat hai aaj main aapke liye AP motor ko winding karne wala hun AP motor ko Kis Tarah Se winding karte hain aur Kaise connection karte hain yah sab aaj main aapko is video mein bataunga isliye video pura Dekhen video Pasand I like Karen doston ke sath channel ko share Karen thank u
playlist
Ap motor
https://dailymotion.com/rss/playlist/x8wz6s
#repairingchannel
#apfan
#motor
#rewinding
Category
ЁЯУЪ
LearningTranscript
00:00I am going to remove the cover of this bag
00:06Let's see what is the problem in this bag
00:09For now, I have removed the cover of this bag
00:13As you can see, there is a lot of dust in this bag
00:16Now, we have to open the front side of this bag
00:20We have to open the front side of this bag
00:22Then only it will open
00:23The bangs of this bag are upside down
00:26That means, if we tighten this bag, it will open upside down
00:34Now, I am going to remove the blade
00:37First, I am going to remove the four screws of the motor
00:40After that, I am going to remove the motor
00:42As you can see, the motor of this bag is of 85W
00:45Let's see what is the problem in this bag
00:48I am going to put this bag on the series
00:51After putting this bag on the series, I am going to check the ground of these three wires
00:58After that, let's see what is the problem in this bag
01:01Now, I have put this bag on the series
01:08Let's check the voltage of this bag
01:11As you can see, there is no current in this bag
01:16As you can see, there is no current in this bag
01:19As you can see, one coil of this bag is working
01:24The series is glowing
01:25And the second red coil is not working
01:29There is no supply in this bag
01:31Let's open this bag and check the motor of this bag
01:35The problem is that the motor of this bag is short
01:40Let's check the winding of this bag
01:44Let's check the number of wires used in this bag
01:49Let's check the winding of this bag
01:53Now, I am going to cut the coils of this bag
02:03As you can see, I have cleaned the stator
02:08I have cut all the coils of this bag
02:13Now, I am going to tell you the basic information about this motor
02:20The size of the stator of this motor is approximately half inch
02:26The width of the stator is more than half inch
02:29There are 24 slots in this stator
02:36There are 4 coils in this stator
02:432 for running and 2 for starting
02:47Let me show you the coils for running
02:57I have made these coils
03:00I have made these coils with copper wire no. 35
03:09The diameter of the coil is 27 inch
03:13I have put 330 turns in it
03:17Similarly, you have to make 2 coils for starting
03:23I have made these coils with copper wire no. 35
03:28The diameter of the coil is 26 inch
03:36I have put 300 turns in it
03:40I have put 300 turns in it
03:45I have put 330 turns in it for running
03:48Similarly, you have to make 3 coils for starting
03:51As you can see, these coils are attached to each other
03:56As I have made a set of 2 coils
03:58As you can see, these coils are attached to each other
04:02You can call it inner coil
04:06You can call it outer coil
04:11I will take this coil and put it inside the stator
04:22I will take this coil and put it inside the stator
04:27You can take any pitch in it
04:37I have started with this
04:39I will show you how to put it
04:45I will show you how to put it
04:51As all coils have to be put in same way
04:57As all coils have to be put in same way
04:59I have put the inner wire in this side
05:03I have put the inner wire in this side
05:08I have put the inner wire in this side
05:10I will put paper inside it
05:16I will put paper inside it
05:21I will put paper inside it
05:31I have put paper inside it
05:35I have put paper inside it
05:37Now we will put coils in same way
05:42Friends, you have to see that we have to put this coil in Pitch 1 to 8.
05:50So, we have to leave 6 slots empty in total.
05:55Suppose, we have put it in 1 slot.
05:57Now, we have to leave 6 slots empty.
06:001, 2, 3, 4, 5, 6
06:03We have left 6 slots empty.
06:05Now, we will put it in the 7th slot.
06:07So, this coil will come in Pitch 1 to 8.
06:11Ok.
06:18Like this.
06:20Friends, it is very easy to put it in.
06:23Because, there is a lot of space in the slots.
06:27You can put it easily.
06:29There will be no problem.
06:31There is no problem of wire cutting.
06:34That wire will be cut or polish will be spoiled.
06:37See, like this.
06:41Put it easily.
06:43Ok.
06:44Like this.
06:45This coil has come.
06:48See, I have put the paper here also.
07:06Friends, see this.
07:07This is the inner wire.
07:10And this wire is attached to the coil.
07:14Ok.
07:15Friends, now what you have to do.
07:18After putting one coil like this.
07:21Now, we have to put coil in Pitch 1 to 10.
07:27So, how we will put it.
07:28Ok.
07:29So, for that what we do.
07:31We turn the coil a little bit.
07:36Ok.
07:37Friends, see like this.
07:39We have to turn the coil.
07:44And after turning, we have to put it inside.
07:47Ok.
07:48So, this coil will be Pitch 1 to 10.
07:53Ok friends.
07:54So, this is our second coil.
07:57We have to bind it and put it in Pitch 1 to 10.
08:01And see like this friends.
08:03Friends, I will show you now.
08:08Like this.
08:11Ok.
08:16Friends, we have to put it like this.
08:18Now, we have to bind the third coil like this and put it inside.
08:25Ok.
08:26Like this.
08:30Friends.
08:33Like this.
08:57See friends.
08:58Friends, like this I have made all the coils.
09:02I have put all three coils.
09:05Now, see this is the second coil.
09:08And how we have to put the second coil.
09:11Friends, we have to put the second coil in the first slot.
09:15Ok.
09:16We have to leave two slots and put it in the third slot.
09:20And leave six slots in the middle and put it in the third slot.
09:25Ok.
09:26We have to leave two slots in the middle and put it in the third slot.
09:28Because from here to here, Pitch 1 to 8 will come.
09:31Then Pitch 1 to 10 will be put in the second slot.
09:36Then Pitch 1 to 12 will be put in the third slot.
09:39The third time coil will be folded and put inside.
09:43Ok.
09:44And like this both the coils will be completed.
09:49So friends, you can see that how to put the second coil.
09:58So friends, you can see that we have put the inner wire in this side.
10:09Ok.
10:10Like this.
10:11Means we have put it in this side.
10:14Now we have to put this coil.
10:17So friends, we have to put the wire of this coil like this.
10:25So friends, the wire of this coil will come in this side.
10:31Ok.
10:32So what we have to do is that we have to reverse the coil.
10:35Like this.
10:36If we reverse the coil, then both the wires will come in front.
10:42Ok.
10:43We have to put it like this.
10:45So we have to put the running coil like this.
10:50And we have to put the starting coil like this.
10:55Ok.
10:56So let me show you.
10:58See, the coil was like this before.
11:02Straight.
11:03Now I have turned it upside down.
11:07Ok.
11:08So we have to put the second coil upside down.
11:12Ok.
11:13Only then our wire will come in front.
11:18So we have to take it like this.
11:22And we have to remove the entire coil inside it.
11:29Ok.
11:30And the wire of this coil will come in this side.
11:34So both of them will come in front.
11:36Ok.
11:37Let me show you by putting it.
11:41See friends, I have put both of its coils.
11:45Now the starting coils will be put in it.
11:49Now the starting coils will be put in it.
11:53Before that, I will stitch it with a cotton tape so that the coils do not get short.
12:03See friends, I have stitched both of its coils.
12:09Now let me put the starting coils in it.
12:15See friends, I have put the coils and stitched it from this side of the motor.
12:24It is completely complete.
12:26I have put the starting and running coils and stitched it.
12:32And see the running and starting coils on this side.
12:36I have not stitched them yet.
12:38Because I have to put a slip pipe in it.
12:43And after joining the wire in it, it will be stitched.
12:50So friends, let me quickly stitch it.
12:55After that I will show you.
13:01See friends, I have stitched both of its coils.
13:04Now let me put the starting and running coils in it.
13:08And see the running and starting coils on this side.
13:12And see the running and starting coils on this side.
13:15And see the starting and running coils on this side.
13:18And see the running and starting coils on this side.
13:21And see the running and starting coils on this side.
13:24And see the running and starting coils on this side.
13:27And see the running and starting coils on this side.
13:30And see the running and starting coils on this side.
13:33And see the running and starting coils on this side.
13:36And see the running and starting coils on this side.
13:39And see the running and starting coils on this side.
13:42And see the running and starting coils on this side.
13:45And see the running and starting coils on this side.
13:48And see the running and starting coils on this side.
13:51And see the running and starting coils on this side.
13:54And see the running and starting coils on this side.
14:18See friends, it is completely completed.
14:21I have put the tape on it.
14:24Now let's put the LED.
14:27See, there is a hole in the rod.
14:30So, put it in the same way as it is in the LED.
14:33So, put it in the same way as it is in the LED.
14:36So, put it in the same way as it is in the LED.
14:42Friends, the bangles are upside down.
14:45It will not be tight on this side.
14:48Friends, the bangles are upside down.
14:51Friends, the bangles are upside down.
14:58Let's put the power LED in it.
15:01Let's put the power LED in it.
15:18Let's put the power LED in it.
15:48Let's put the power LED in it.
16:18Let's put the power LED in it.
16:21Let's put the power LED in it.
16:44Friends, I have tightened its cover.
16:47Friends, I have tightened its cover.
16:50Let's check it for the last time.
16:53Let's check it for the last time.
17:01I have completed it fully.
17:04I have completed it fully.
17:07And for now, this is its main wire.
17:10And for now, this is its main wire.
17:20I have connected the main wire to the main board.
17:31First I will watch it on series then I will connect it directly.
17:37I have connected it on series and it is working fine.
17:43Friends, I have connected it on series and it is working fine.