Mini Wind Turbine | Vertical Axis wind Mill | DIY Project| How to make tutorial
Make mini wind turbine at home \r
\r
\r
This mini wind turbine is very easy to make ansd can be used to recharge your smartphone. Make this mini wind turbine for kids. Mini wind turbine design for school project.\r
\r
Click like button then start making your own small wind tutbine \r
\r
How to make Wind turbine (Vertical Axis). Step by step Instructions to make working model of small wind turbine or Vertical axis wind turbine (VAWT)\r
\r
Things needed to Make Vertical Axis Wind Turbine\r
\r
4” PVC Pipe 30 cm in length\r
ACP Sheet 30cm in length\r
Dynamo 3-5 Volt\r
PVC or CPVC Fittings 3Ts and 4 Elbows\r
Pieces of PVC or CPVC Pipe\r
L-Clamp Steel 4\r
Plate washer 2” IN Dia- 2\r
GI Nut that suits Dynamo Pulley\r
Connecting Wires\r
3/4” Cycle Screws 30\r
Powerbank\r
\r
Tools needed to Make Vertical Axis Wind Turbine\r
\r
Angle Grinder\r
Drilling machine\r
6mm drill bit\r
Welding machine (optional)\r
Multimeter\r
Spanner set\r
Other necessary equipment\r
\r
How to Make Vertical Axis Wind Turbine (VAWT)\r
\r
Step 1\r
\r
Take PVC Pipe having 4inch diameter and 30 cm length.\r
Axially divide it into 4 equal parts using an angle grinder\r
Carefully use angle grinder\r
Make holes on one side of the PVC using 6mm drill bit\r
PVC 4 30cm\r
PVC 4” 30cm\r
PVC Pieces\r
PVC Pieces\r
Sep 2\r
\r
Cut 4 pieces of ACP Sheet having 30 cm in length and 6 cm in width\r
Mark holes on ACP from PVC Pieces and make holes Using 6mm drill bit.\r
ACP Pieces\r
ACP Pieces\r
\r
Step 3\r
\r
Buy 4 steel L-clamps and cut it into required length (12 cm * 6 cm) using an angle grinder.\r
Take care and wear glasses while using an angle grinder.\r
L clamp\r
L clamp\r
\r
Step 4\r
\r
Take GI Plate washer 2” in diameter\r
Take a GI nut that suits dynamo pulley\r
Weld GI Nut at the center of the plate washer\r
Then weld all 4 L-Clamps on the plate washer\r
Propeller frame is ready.\r
Plate Washer\r
Plate Washer\r
Plate washer and Nut\r
Plate washer and Nut\r
Welding\r
Welding\r
Propeller Frame\r
Propeller Frame\r
\r
Step 5\r
\r
Connect ACP Sheets and PVC pieces together using cycle screws.\r
Use a spanner to tighten it.\r
Then connect these propeller blades on propeller frame.\r
Wind turbine propeller is ready.\r
Propeller Frame\r
Propeller Frame\r
propeller propeller2\r
Step 6\r
\r
Buy PVC or CPVC fittings (4 elbows, 3 Ts).\r
Join these components together to make wind turbine base.\r
Connect the wire to the dynamo and fix it on wind turbine base.\r
CPVC Fittings\r
CPVC Fittings\r
Wind Turbine Base\r
Wind Turbine Base\r
Dynamo\r
Dynamo\r
Step 7\r
\r
Place propeller on the wind turbine base.\r
Vertical axis wind turbine is ready.\r
Place the wind turbine in front of a Fan.\r
Yeah. Its working fine\r
Check the output voltage using a multimeter.
\r
\r
This mini wind turbine is very easy to make ansd can be used to recharge your smartphone. Make this mini wind turbine for kids. Mini wind turbine design for school project.\r
\r
Click like button then start making your own small wind tutbine \r
\r
How to make Wind turbine (Vertical Axis). Step by step Instructions to make working model of small wind turbine or Vertical axis wind turbine (VAWT)\r
\r
Things needed to Make Vertical Axis Wind Turbine\r
\r
4” PVC Pipe 30 cm in length\r
ACP Sheet 30cm in length\r
Dynamo 3-5 Volt\r
PVC or CPVC Fittings 3Ts and 4 Elbows\r
Pieces of PVC or CPVC Pipe\r
L-Clamp Steel 4\r
Plate washer 2” IN Dia- 2\r
GI Nut that suits Dynamo Pulley\r
Connecting Wires\r
3/4” Cycle Screws 30\r
Powerbank\r
\r
Tools needed to Make Vertical Axis Wind Turbine\r
\r
Angle Grinder\r
Drilling machine\r
6mm drill bit\r
Welding machine (optional)\r
Multimeter\r
Spanner set\r
Other necessary equipment\r
\r
How to Make Vertical Axis Wind Turbine (VAWT)\r
\r
Step 1\r
\r
Take PVC Pipe having 4inch diameter and 30 cm length.\r
Axially divide it into 4 equal parts using an angle grinder\r
Carefully use angle grinder\r
Make holes on one side of the PVC using 6mm drill bit\r
PVC 4 30cm\r
PVC 4” 30cm\r
PVC Pieces\r
PVC Pieces\r
Sep 2\r
\r
Cut 4 pieces of ACP Sheet having 30 cm in length and 6 cm in width\r
Mark holes on ACP from PVC Pieces and make holes Using 6mm drill bit.\r
ACP Pieces\r
ACP Pieces\r
\r
Step 3\r
\r
Buy 4 steel L-clamps and cut it into required length (12 cm * 6 cm) using an angle grinder.\r
Take care and wear glasses while using an angle grinder.\r
L clamp\r
L clamp\r
\r
Step 4\r
\r
Take GI Plate washer 2” in diameter\r
Take a GI nut that suits dynamo pulley\r
Weld GI Nut at the center of the plate washer\r
Then weld all 4 L-Clamps on the plate washer\r
Propeller frame is ready.\r
Plate Washer\r
Plate Washer\r
Plate washer and Nut\r
Plate washer and Nut\r
Welding\r
Welding\r
Propeller Frame\r
Propeller Frame\r
\r
Step 5\r
\r
Connect ACP Sheets and PVC pieces together using cycle screws.\r
Use a spanner to tighten it.\r
Then connect these propeller blades on propeller frame.\r
Wind turbine propeller is ready.\r
Propeller Frame\r
Propeller Frame\r
propeller propeller2\r
Step 6\r
\r
Buy PVC or CPVC fittings (4 elbows, 3 Ts).\r
Join these components together to make wind turbine base.\r
Connect the wire to the dynamo and fix it on wind turbine base.\r
CPVC Fittings\r
CPVC Fittings\r
Wind Turbine Base\r
Wind Turbine Base\r
Dynamo\r
Dynamo\r
Step 7\r
\r
Place propeller on the wind turbine base.\r
Vertical axis wind turbine is ready.\r
Place the wind turbine in front of a Fan.\r
Yeah. Its working fine\r
Check the output voltage using a multimeter.